Duct leakage is the gap between the heat a furnace makes and the heat that reaches the rooms, and in a Modesto attic that gap is a fifth to a third of the furnace’s output by the national estimates. This guide gives the signs, how the test measures it, what the state requires at replacement, and what sealing costs.
How do I know my ducts leak?
Every duct system leaks somewhat. The question is how much, and the signs are indirect because the ducts are in the attic. ENERGY STAR’s estimate is that in a typical house about 20 to 30 percent of the air that moves through the duct system is lost due to leaks, holes and poorly connected ducts (ENERGY STAR). The Department of Energy’s duct guide puts the energy side higher, at 25 to 40 percent of the heating or cooling energy the furnace puts out, and adds a detail that explains why: the cracks in ductwork typically have an area that is 10 to 20 percent of the leakage area of the whole house (DOE, Improving the Efficiency of Your Duct System). A tenth to a fifth of all the holes in the house are in the ducts, and the furnace fan pressurizes them.
| Sign | Why leakage causes it |
|---|---|
| Rooms at the end of long runs never warm up | The run loses air and heat before the register |
| Supply air at a far register is 10 degrees cooler than near the furnace | Heat lost through the duct wall and leaks in a cold attic |
| Dust streaks on registers, dusty house with a clean filter | Return-side leaks pull attic dust into the system |
| Therms up year over year with the same thermostat | The furnace runs longer to replace lost heat |
| Furnace cycles more than it used to | Lost supply air lengthens every call |
| A musty or attic smell when the fan starts | Return leaks drawing attic air |
| Flex duct visibly sagging, kinked or disconnected from the hatch | The leak itself |
Two of those are checks you can make. The register temperature comparison, near the furnace against the far room, takes a thermometer and ten minutes; the cold-room guide walks it step by step. See the register temperature check that finds a cold room’s cause. And a look into the attic from the hatch with a flashlight, without walking the joists, often shows a run that has fallen off its boot or a joint with the tape hanging loose.
How is duct leakage tested?
With a fan and a gauge, not a guess. A duct leakage test seals every register and return with tape or plugs, connects a calibrated fan to the system, pressurizes the ducts to a standard pressure, and measures how much air the fan has to move to hold that pressure. That airflow is the leakage, expressed as a percentage of the furnace’s rated airflow. A second version, leakage to outside, pressurizes the house and the ducts together so that leaks into the living space do not count, and measures only what escapes to the attic and outdoors, which is the number that costs you money.
California’s energy code uses exactly this test. The compliance form for alterations to space conditioning systems states that a duct leakage test is required when heating or cooling components are installed in ducted systems, or when more than 25 feet of duct is replaced, verified by a HERS rater, with the leakage rate compliance at 10 percent or less, or 7 percent or less to outside, or sealing all accessible leaks where the target cannot be met; duct systems previously registered as sealed, and systems insulated or sealed with asbestos, are exempt (California Energy Commission, CF1R-ALT-02-E). So a furnace replacement in Modesto comes with this test by law, and the HERS rater’s number is a document you can keep. HomeGuide notes that many technicians perform a pressure test for $200 to $450 (HomeGuide), which is the standalone price when no furnace is being replaced.
What does duct sealing cost?
HomeGuide’s 2026 guide puts air duct sealing at $1 to $2 per square foot, or $1,000 to $6,000 total, depending on house size, sealing method, duct accessibility and local labor rates, with the Aeroseal brand of aerosol sealing at $1,500 to $6,900 on average and duct insulation at $1 to $13 per square foot (HomeGuide). Those are national reported ranges, not this business’s prices.
| Method | What it does | HomeGuide range | Best for |
|---|---|---|---|
| Manual sealing with mastic and foil tape | A technician seals each accessible joint, boot and seam by hand | Within the $1,000 to $6,000 whole-house range | Accessible attic ducts, large gaps, disconnected runs |
| Aerosol sealing | A sealant mist is blown through the pressurized ducts and sticks in the leaks from inside | $1,500 to $6,900 | Leaks that cannot be reached, many small gaps |
| Insulation added to sealed ducts | Cuts heat loss through the duct wall in the attic | $1 to $13 per square foot | Every attic run, after sealing |
| Pressure test alone | Measures leakage before and after | $200 to $450 | Deciding whether sealing is worth it |
ENERGY STAR’s own guidance is the order of operations: seal air leaks using mastic sealant or metal-backed foil tape, insulate all the ducts you can access, including those in attics, crawlspaces and garages, and never use standard cloth duct tape because it fails (ENERGY STAR). Sealing first, insulation second, and a test on each side of the work so the improvement is a number.
Is it worth sealing the ducts?
Run the arithmetic on your own bill. If the ducts are losing a quarter of the furnace’s output to the attic, a quarter of the winter’s therms are buying heat the house never receives, and the diagnosis of a bill that rose without the weather explaining it is in why a heating bill is so high and how to read therms and kilowatt-hours. On a gas bill that is a real share of three months of heating; on a heat pump it is the same share of kilowatt-hours, plus the strips that run when the house cannot reach temperature. Against that sits a one-time cost in HomeGuide’s range, with the test to prove the result.
Supply and return leaks cost you differently. A supply leak throws heated air into the attic, which is money. A return leak pulls attic air, dust and whatever is near a water heater flue into the system, which is money and air quality at once, and it is the reason a house with a clean filter can still be dusty. The leakage-to-outside test does not distinguish them, but a technician with a smoke pencil at the return side does, and the return boots near the furnace are usually the first thing sealed.
The honest caveats. Sealing recovers the leak, not the heat lost through the duct wall, which is why insulation follows it. A system with 30 percent leakage that is sealed to 8 does not cut the bill by 22 percent, because some of that leaked air was leaking into the house rather than the attic. And sealing does nothing for an oversized furnace or a starved return. The test tells you which of those you have before you spend.
What does the Modesto attic do to ducts?
It ages them. Flex duct in an attic that reaches well over a hundred degrees every summer afternoon has its outer jacket and inner liner cycled through heat for decades, the tape at the joints dries and lets go, and the mastic that was never applied was never there to hold. The runs sag between joists and kink where they were laid across a truss web. Harvest dust settles on everything and is pulled into every return-side leak. A thirty-year-old duct system in this valley has usually had more done to it by the attic than by any installer, and it is often leakier than the furnace it serves is inefficient. The pre-winter tune-up that measures airflow and temperature rise is the visit that first notices it, and what that visit should include is in the furnace tune-up checklist.
Duct leakage on a new furnace?
Duct leakage is the thing most likely to make a new furnace disappoint. A higher-efficiency unit with a stronger blower on the old ducts pushes more air out through the same leaks, the far rooms are no warmer, and the bill does not fall the way the AFUE number promised. California’s test requirement at replacement exists for exactly this reason, and a contractor who skips the permit skips the test. The right sequence on a replacement in Modesto is the leakage test, sealing to pass it, insulation on the attic runs, and then the furnace sized to the house with its ducts fixed, which is why the furnace maintenance and duct testing visit belongs before the installation quote rather than after it. The wider picture of winter comfort, safety and costs is in the guide to winter comfort, safety and energy costs in a Modesto home.
When should you call a professional?
The safety line first. A gas smell means leave the house and call 911 from outside, then the gas utility. A carbon monoxide alarm means the same. Neither is a duct question, though a return leak near a garage or a water heater flue can carry fumes into the system, which is one more reason the test matters.
Call for the leakage test, for the sealing and insulation, and for any run that has to be reached by walking attic joists over a ceiling, which is a fall and a foot through the drywall waiting to happen. The register comparison, the look from the hatch, and the open registers are yours. Everything in the attic is the technician’s, with the fan and the gauge that turn a cold room into a number.
Frequently asked questions
How do I know if my ducts leak?
Far rooms that never warm, supply air ten degrees cooler at a distant register than near the furnace, dust with a clean filter, therms rising without a weather explanation, and visible sagging or disconnected runs from the hatch. ENERGY STAR’s typical figure is 20 to 30 percent of duct air lost, so some leakage is assumed; the test measures how much.
How is duct leakage tested?
Registers are sealed, a calibrated fan pressurizes the ducts, and the airflow needed to hold the pressure is the leakage, as a percentage of the furnace’s airflow. California requires the test, HERS-verified, when heating or cooling components are installed in ducted systems or more than 25 feet of duct is replaced. Standalone, HomeGuide puts a pressure test at $200 to $450.
What does duct sealing cost?
HomeGuide’s range is $1 to $2 per square foot, or $1,000 to $6,000 for a house, with aerosol sealing at $1,500 to $6,900 and duct insulation at $1 to $13 per square foot. Those are national reported ranges, not local prices.
Can I seal the ducts myself?
The accessible joints near the furnace, with mastic or foil tape rather than cloth duct tape, yes. The attic runs are a fall risk and most of the leakage, and the test that proves the result needs a calibrated fan. Treat it as a technician’s job with a before-and-after number.
Does it matter more in Modesto?
Yes, because nearly every run is in an attic that is cold on January nights and hot every summer afternoon, which both loses heat and ages the ducts. Decades of that, plus harvest dust pulled into return leaks, leave many valley duct systems leakier than the furnace they serve is inefficient.
The short version
Assume a fifth to a third is leaking, by ENERGY STAR and the DOE. Confirm it with the register comparison and a look from the hatch, then a pressure test. Seal with mastic, insulate the attic runs, test again. Expect the test by law when the furnace is replaced, and do the ducts before the new furnace rather than after. The number on the rater’s form is the proof.