A water heater pilot light is the small standing flame that lights the main burner on many gas tanks. When it keeps going out, the usual causes are a weak thermocouple, drafts, a blocked air supply or a gas supply problem. If you smell gas, do not touch it: leave the house and call 911 from outside.
This is a diagnosis guide, not a repair guide. It explains what the pilot does, what makes it fail, what you can safely observe, and when the job belongs to a professional. Relighting is covered only by pointing you to the instructions printed on your own heater, because those instructions are written for that exact model.
What does the pilot light do?
On a standing-pilot gas tank, a small flame burns all the time beside the main burner. When the thermostat calls for heat, the gas control opens the main burner valve, and the pilot lights the main burner. The pilot also heats a safety sensor, a thermocouple or a thermopile.
That sensor is the reason a pilot outage is a safety feature, not just an inconvenience. A.O. Smith explains that if the pilot goes out, the thermocouple or thermopile is no longer energized and the pilot safety valve shuts off the gas flow, and that if the thermocouple itself is broken, the safety valve does not receive power, so the pilot will not stay lit (A.O. Smith, How to Light a Pilot Light). In other words, when the flame dies, the heater is designed to stop the gas.
Not every gas water heater has a standing pilot. Many newer units use electronic or spark ignition with no flame until heat is needed. If your heater has a glass sight window and a control marked pilot, it likely has a standing pilot. If not, the ignition system is different, and the label will say so.
Gas heat is common here. Census figures for Modesto show utility gas as the heating fuel in about 64% of occupied homes, based on ACS 2024 one-year data (Census Reporter, ACS table B25040). That figure is for space heating, not water heating, but it shows how many homes have a gas supply, and so how many may depend on a water heater pilot light working as designed.
Why does the pilot keep going out?
A.O. Smith lists gas pressure changes, drafts and blocked combustion air as things that can put the pilot out, along with clogged or kinked gas tubes, ignition system failure and control valve failure (A.O. Smith). Grouped by how they show up:
- A weak or failing thermocouple or thermopile. The pilot lights but goes out when the control is released or a short time later. This is the most common pattern on an older heater.
- A dirty or clogged pilot. A small, yellow or flickering flame does not heat the sensor well. Dust and lint in a garage are common sources.
- Drafts. A door, fan or open garage near the heater can blow the flame out, especially on windy days.
- Not enough combustion air. Stored items crowding the heater or a closet with no air opening starve the flame.
- Gas supply problems. Pressure changes or a supply issue upstream affect every gas appliance, not just the heater.
- Venting problems. A blocked, disconnected or shared vent can cause spillage and flame outages.
- A failed gas control. If the sensor and pilot are fine, the control itself may be the fault.
Reading the flame
The flame itself is the best clue a homeowner has, and you can read it through the sight window without opening anything. A steady, mostly blue water heater pilot light that wraps the tip of the thermocouple is what a healthy standing pilot usually looks like. Several other patterns each point somewhere different:
- Small and weak. A flame that barely reaches the sensor may not heat it enough to hold the safety valve open. Dirt in the pilot or low gas pressure are the usual suspects.
- Yellow, lazy or sooty. This suggests poor combustion, often from dirt or too little air. Soot or scorch marks around the burner door make it more serious. Do not keep running a heater that shows soot; have it checked.
- Lifting or flickering. A flame that dances or lifts away from the pilot can mean drafts in the room or a draft problem in the vent.
- Goes out when another appliance starts. If the pilot dies when the furnace or a strong exhaust fan comes on, the room may be short of air or the vent may be affected.
Write down what you see and when. A technician who knows the flame was yellow on cold mornings, or went out every time the furnace started, can go straight to the likely cause.
Air supply is a safety issue
Blocked combustion air is not only a reason the pilot dies. A.O. Smith warns that a lack of combustion air can result in unburned fuel and carbon monoxide being released into the home (A.O. Smith).
Venting changes made by other work are a hidden cause. A gas water heater sometimes shares a vent with a furnace, and when the furnace is replaced, the vent may be changed too. A pilot that started going out soon after a furnace or roof job deserves a vent check by a qualified technician. Do not try to adjust or reconnect vent pipe yourself.
What you can safely check
These checks involve looking, not touching gas parts. If you smell gas at any point, stop and go straight to the safety line below.
- Is it only the water heater? If a gas range or furnace also will not light, the issue may be the gas supply, not the heater. Call your gas utility.
- Look through the sight window. A healthy standing pilot is usually a steady blue flame. A lazy yellow flame or no flame tells the technician something.
- Clear the area. Move stored items, boxes, paint, gasoline and other flammables well away from the heater. Flammable vapors near a gas appliance are a fire hazard.
- Note the pattern. Does it go out on windy days, when the garage door is open, after the furnace starts, or randomly? That pattern helps narrow the cause.
- Check the age. The label usually encodes the manufacture date in the serial number.
- Check the CO alarm. Make sure a working carbon monoxide alarm is installed nearby and on every level.
Relighting: follow the label only
We do not give step-by-step relighting instructions. Every gas heater has its own lighting instructions on a label on the unit, and A.O. Smith says those instructions supersede its own general guide and that owners should read and follow every label before any troubleshooting (A.O. Smith). The same page says not to continue if you smell gas.
If the label is missing or unreadable, if the pilot will not stay lit after you follow the label once, or if you are not comfortable working near a gas control, stop and call a professional. A pilot that goes out repeatedly is telling you something is wrong, and relighting it again and again does not fix the cause.
Diagnosis a technician will run
Knowing what a professional checks helps you judge whether you are being sold the right part. For a pilot that will not stay lit, a technician typically:
- inspects the pilot flame and cleans the pilot assembly if it is dirty;
- tests the thermocouple or thermopile output, rather than replacing parts by guesswork;
- checks gas pressure at the appliance;
- checks the vent for blockage, disconnection and correct draft, including when a shared furnace runs;
- confirms enough combustion air reaches the heater;
- tests the gas control if everything else checks out.
Ask for the finding in writing, including what was tested and the reading. A water heater pilot light problem that is fixed by guessing often comes back, because a new thermocouple will not cure a draft or venting fault. A thermocouple is a small part; a gas control is a major component; a venting fault may be outside the heater entirely.
Repair or replace a gas heater
Use the heater’s age and the part that failed:
- Under 8 years old with a minor fault, such as a thermocouple or a dirty pilot: repair.
- Over 10 years old, or a major component has failed, such as the gas control or the tank: replace.
- Over 12 years old: replace regardless.
Hard water matters here too. The City of Modesto’s 2025 water quality report lists average hardness at 199 mg/L as calcium carbonate (City of Modesto 2025 Consumer Confidence Report), and sediment on the bottom of a gas tank shortens its life. If the heater is older and the pilot problem points to the gas control, replacement is usually better value than a costly part on a tired tank. If water is also showing up around the base, see our guide to a water pooling under the heater.
Is it the pilot or another fault?
No hot water does not always mean the pilot is out. On an electric heater there is no pilot at all, and the causes are elements, thermostats and the breaker. On a gas heater, a lit pilot with no hot water points to the gas control, the thermostat setting or the main burner. Our guide to no hot water in the house walks through the order of checks for each type. For the wider picture, see our guide to gas water heater problems.
When to call a professional
Call a professional when the pilot will not stay lit after following the label once, when it goes out repeatedly, when the flame looks yellow or lazy, when there is soot or scorching around the burner door, when the vent looks disconnected, or after any furnace or vent work. Gas controls, burners, gas lines and venting are for a qualified technician. Homeowners should diagnose by observation only.
Hard safety line: if you smell gas, do not relight anything, do not touch light switches, phones or flames inside, and do not try to find the leak. Leave the house, then call 911 and your gas utility, PG&E, from outside. A.O. Smith also says not to relight the pilot if you smell gas (A.O. Smith). If a carbon monoxide alarm sounds or anyone has a headache, dizziness, weakness, nausea or confusion, get outside to fresh air immediately, then call 911. The U.S. Consumer Product Safety Commission gives that advice whenever carbon monoxide poisoning is suspected (CPSC Carbon Monoxide Information Center).
For a water heater pilot light that keeps going out in Modesto, AC Service Modesto can diagnose the cause and tell you whether it is a part or a replacement. Call (209) 439-1859 or see our Modesto water heater repair page.
Frequently asked questions
Is it dangerous if the pilot light goes out on a water heater?
On its own, usually not, because the safety valve is designed to shut off the gas when the flame goes out. It becomes dangerous if you smell gas or if the cause is blocked air or venting, which can release carbon monoxide. Smell gas: leave and call 911 from outside.
Why won’t my water heater pilot light stay lit?
The most common cause is a weak thermocouple or thermopile that no longer holds the safety valve open. Dirty pilots, drafts, low combustion air, gas supply issues, venting faults and a failed gas control are the others. A technician can test which one it is.
Can I relight the pilot light myself?
Only by following the lighting instructions on your heater’s own label, and never if you smell gas. If it will not stay lit after one attempt, stop. Repeated relighting does not fix the cause, and the fault needs a professional diagnosis.
Do all gas water heaters have a pilot light?
No. Many newer gas water heaters use electronic or spark ignition with no standing flame. Your heater’s label and manual state which type it has and how its ignition works.